First repair with us: up to $15 off the repair
$85 diagnostic, counted inside the repair you approve
$10 off a second appliance’s diagnostic
Dryers · gas homes · Brier
Clothes still damp after a second cycle, or a gas dryer that tumbles without heat? In Brier, where most houses have gas service, we meter igniters, coils and fuses, and we always follow the vent outdoors.
Booking
Tell us the machine and what it is doing, then where to come. We call back to set a two-hour window, Monday through Saturday.
Prefer to talk? (425) 905-3879 · Mon–Sat 8 a.m.–7 p.m. · Sunday closed
Dryers · Brier
About two-thirds of Brier homes heat with piped natural gas, and once gas is piped to the laundry, a gas dryer usually follows. So our Brier dryer work leans toward igniters, valve coils and flame sensors, though plenty of electric dryers still turn up in older ranches and garage laundries. Vent routes vary with the house. A laundry off the garage may exhaust straight through a nearby wall, while a dryer in the middle of a two-story house can push its air along a lengthy run under the floor and across a crawlspace. Beneath tall trees those runs stay cool and damp, and convergence-zone storms along the King–Snohomish county line keep wet coats and towels coming. Moisture condenses inside long ducts, binds the lint into a paste, and slows every load.
Most dryer failures in Brier begin with airflow. A restricted vent holds hot, wet air in the drum, loads take longer, and the cabinet runs hotter until the thermal fuse or the high-limit opens. On gas dryers, the igniter and the valve coils are the next suspects, and one pattern repeats: the burner lights, runs briefly, and then leaves the drum tumbling cold for the rest of the cycle. On a recent call of exactly that kind, the technician saw the igniter brighten and the burner light, then saw it fail to relight once the first flame cycled off. The meter showed one valve coil opening up as it warmed. A fresh coil set from the van, a vacuumed burner area and a complete heat cycle confirmed the repair.
Symptoms
| What you notice | Usually behind it | What we do on the visit |
|---|---|---|
| Drum turns but never warms | Open thermal fuse, or a dead igniter or element | Meter the fuse and heat source, then find why the fuse blew |
| Gas dryer lights, then goes cold mid-cycle | Valve coils weakening once they warm up | Observe ignition, meter the coils, fit a fresh set |
| Loads need a second or third cycle | Lint-choked or crushed vent run | Measure hood airflow, trace the duct, show you the restriction |
| Scorched smell or a top panel too warm to rest a hand on | Lint packed near the burner tube or element can | Shut it down, clean inside the cabinet, test both limits |
| Thump or squeal as the drum turns | Rollers worn flat, an idler pulley with a dry bearing, or a frayed belt | Swap the worn pieces and listen through a test tumble |
Calls in Brier
Ranch house · electric dryer in the garage laundry
An electric dryer ran and tumbled but stayed cold. The meter found the heating element open, and the technician spotted a broken coil that had sagged against its housing. Before fitting a new element, the technician tested both thermostats, cycling and high-limit, then followed the vent and found a crushed foil section behind the machine that had kept it running hot.
Wooded lot near Brier Road · vent hood under the eaves
Drying times had stretched all through a wet fall. The dryer itself tested fine, so the technician went outside and found the vent hood’s flap gummed shut with damp lint and needles from the trees overhead, trapping moisture in the duct. With the hood cleared, airflow at the outlet came back strong, and the next load finished in a single cycle.
1990s house · squealing gas dryer
A gas dryer squealed at the start of every load and thumped once it warmed. Inside the cabinet, the idler pulley had a dry bearing and two drum rollers were worn flat on one side. The technician replaced the pulley, the rollers and the belt, vacuumed lint from around the burner, and ran a load to listen for anything left.
On the visit
On a dryer call, the vent comes first. The technician reads the air speed at the exterior hood and inspects the transition duct behind the machine, because no part stays fixed if the air cannot leave. Next the cabinet opens, and the meter goes to the thermal fuse, then to the high-limit and cycling thermostats, then to the moisture sensor bars. On a gas dryer, the igniter’s resistance is read, the flame sensor is tested, and the technician watches a full ignition sequence to see whether the valve coils hold. On an electric dryer, the heating element and the supply at the terminal block are tested, along with the breaker that feeds it. Belts, rollers and the idler pulley get checked for wear. If a fuse has opened, you hear what made it open.
Brier laundry rooms hold Whirlpool, Maytag and Kenmore dryers in both fuel types, along with GE, LG, Samsung and Electrolux machines bought as matched pairs with a front-loader. A few houses run Speed Queen, chosen for its simple controls. Because these homes are owner-occupied and laundry rooms rarely move, a dryer often inherits the same vent route through two or three replacements, and that route is where many of the problems live. Igniters, coils, fuses, thermostats and belts for the common models ride in the van, so many dryer repairs finish on the first visit. If the manufacturer’s warranty still covers a newer dryer, you hear that first. Give the go-ahead and your $85 diagnostic is counted within the dryer repair; decline, and $85 is the full invoice.
FAQ
Yes, and they fill a big part of our Brier dryer schedule, since most houses here have gas service. The technician tests the igniter, the flame sensor and the coils on the gas valve with a meter, inspects the burner, and watches the flame through a complete heat cycle. Electric dryers get the same care, from the element to the thermostats.
Watch for loads that want another round, a laundry room that turns humid, a top panel that feels hot, or a hood outside that barely flutters while the dryer runs. Any of these suggests the air is not escaping as it should. On every visit the technician reads airflow at the hood and reports whether the run needs cleaning or rerouting.
Think of the fuse as a one-shot safety link: it breaks when the cabinet gets too hot, and airflow is nearly always why: a lint-packed vent, a flattened duct, or a hood flap stuck shut. Sometimes a cycling thermostat or a gas valve fault is to blame. Replacing the fuse alone only postpones the next failure, so the technician finds the cause before closing up the dryer.
It can. Cool, moist air under tall trees and the extra rain near the county line mean more wet loads and more condensation in long vent runs, especially through crawlspaces or garages. Water collecting in a sag in the duct traps lint and narrows the passage. We look for sags and low spots as part of the airflow test.
Better not. Stop the cycle, let the dryer cool, and keep it switched off until someone has looked inside. That odor usually comes from lint gathered near the burner or element, or from a blocked vent. Empty the lint screen and glance at the vent hood outdoors when it is within easy reach, then phone us or book a visit online.
Most dryer parts, from fuses and thermostats to igniters, rollers and belts, are worth replacing on a sound cabinet. A rusted drum or a failed control on an aging machine changes the math. We name the failed part, write one price, and if we think replacement is the wiser choice, we say so.
More repairs in Brier
Dryer Repair nearby
Parts behind these calls
Book the $85 diagnostic visit
A Brier dryer diagnosis costs $85, and that amount is contained in the repair you approve; it is the whole cost only when you decide to leave the machine as it is.