First repair with us: up to $15 off the repair
$85 diagnostic, counted inside the repair you approve
$10 off a second appliance’s diagnostic
Ice makers · Meadowdale to Seaview
No ice since the power came back, a bin of hollow cubes, a fill tube frozen solid? Edmonds ice maker repair happens inside your refrigerator: the technician tests the inlet valve, module and fan, then prices it in writing.
Booking
Tell us the machine and what it is doing, then where to come. We call back to set a two-hour window, Monday through Saturday.
Prefer to talk? (425) 905-3879 · Mon–Sat 8 a.m.–7 p.m. · Sunday closed
Ice makers · Edmonds
Snohomish County PUD supplies Edmonds with power, and when the November 2024 bomb cyclone left more than 70,000 of its customers in the dark at the peak, ice makers were among the machines that didn’t come back on their own. Some modules need a full cycle or a reset after a long outage. Some sat with a half-filled mold that froze around the ejector arm. Others had a fill tube that iced shut while the freezer warmed and then cooled again. Calls about bins that never refilled followed once the lights returned. Outside of storms, ice makers here lead fairly quiet lives. The water is very soft, so mineral scale rarely blocks a valve or a fill tube, and the cause of a stoppage is usually mechanical or electrical.
Most ice maker faults sit somewhere along a short chain: the water inlet valve that opens to fill the mold, the fill tube that carries water into the freezer, the ice maker assembly with its motor, thermostat and ejector, and the fan that keeps the freezer cold enough to freeze the cubes. A broken link anywhere halts production. Door-mounted ice makers on French-door refrigerators add a separate compartment with its own fan and seals, and frost there is a frequent culprit. A typical call: a French-door refrigerator in a house near the Edmonds Marsh, with the ice in the door bucket fused into a single block. The compartment gasket had torn, warm air leaked in, and cubes melted and refroze. A new gasket and a cleared chute got the dispenser working again.
Symptoms
| What you notice | Usually behind it | What we do on the visit |
|---|---|---|
| No ice since a power outage | Module stalled mid-cycle or a frozen fill tube | Thaw the tube, run a test cycle, meter the module |
| Small, hollow or clumped cubes | Low fill from a weak valve or a clogged screen | Measure the fill, clean the screen, test the valve coil |
| Ice maker hums, but no water arrives | Open inlet valve coil or a kinked supply line | Check supply pressure, meter the valve, replace it |
| Ice fused together in the door bucket | Door compartment gasket or fan letting warm air in | Inspect seal and fan, clear the chute and auger |
| Water dripping behind the refrigerator | Cracked inlet valve or a loose supply fitting | Find the drip, replace the valve, tighten the connection |
Calls in Edmonds
Meadowdale · no ice after the windstorm
After the November 2024 outage, the refrigerator cooled again but the ice maker sat idle with a half-frozen tray. The technician thaws the fill tube, puts the module through its test mode and watches the ejector sweep. The water inlet valve passes on the meter. A full batch of cubes drops into the bin before the van pulls away.
Seaview · built-in with thin cubes
A built-in refrigerator in a remodeled view-home kitchen turns out thin, half-sized cubes. With water this soft, scale gets ruled out early. The inlet screen is clean, but the valve opens weakly and the fill measures short. A replacement valve goes in, and the next harvest comes out as full, solid cubes.
Edmonds Way · slow ice after a filter change
A French-door refrigerator in a house off Highway 104 makes ice slowly ever since a new water filter went in. The cartridge is seated a fraction short, which throttles the flow. The technician reseats it properly, checks flow at the dispenser and meters the inlet valve to confirm there isn’t a second problem hiding behind the first.
On the visit
The technician checks the freezer temperature first, since an ice maker in a freezer that is too warm will never harvest. Next comes the supply: the shutoff valve, the line behind the refrigerator and the water filter, because a clogged filter or a kinked line can pass for a bad valve. Then the inlet valve is measured with the meter, both for coil resistance and for voltage when the ice maker calls for water. The fill tube is checked for ice where it enters the freezer. The ice maker assembly goes into its test cycle so the motor, the ejector and the mold heater can be watched releasing the cubes. On door-ice models the compartment fan, the gasket and the auger motor are tested as well. When a part fails, you hear which one, in plain words.
Ice makers around Edmonds sit in French-door refrigerators from GE, LG, Whirlpool and KitchenAid, side-by-sides from Frigidaire, Kenmore and Maytag, and panel-front built-ins by Café, Miele and Thermador in rebuilt kitchens. Plenty of houses with a garage refrigerator have a second ice maker out there, sometimes disconnected for years and then suddenly put back to work. We repair ice makers built into refrigerators and freezers; standalone ice machines are outside what we offer. If your refrigerator is still within its maker’s warranty, we say so first. The money side stays plain: the $85 visit is folded into the cost of a repair you approve, and if you choose not to repair, the $85 is the total.
FAQ
Some ice makers stall mid-cycle when the power drops, with water frozen around the ejector or inside the fill tube. Others wait for the freezer to reach temperature before they start, which takes a while after a long outage. If a full day passes and the bin is still empty, the technician can thaw, test and reset it.
Yes. An ice maker depends on the freezer around it, so the cause often turns out to be there: a failing evaporator fan, a defrost fault or a worn gasket. The technician checks both, and the written price covers whatever the repair involves, so there are no surprises later.
Too little water reaching the mold. With Edmonds water as soft as it is, scale is rarely the reason. A clogged filter, a kinked line behind the refrigerator, low supply pressure or a weak inlet valve is more likely. We measure the fill and test the valve with a meter before replacing anything.
No. We work on ice makers built into home refrigerators and freezers, including door-ice models and built-ins. Standalone undercounter ice machines and commercial units fall outside our service list, and we would rather tell you that on the phone than after a trip out.
Often. A cracked water inlet valve or a loose fitting at the supply line can drip slowly for weeks before anyone notices. Shut off the water to the refrigerator if you can, lay a towel down and book a visit. The technician finds the source and replaces the valve or fitting.
Typically within a day, Monday through Saturday, and morning calls have the strongest shot at a same-day slot. If the whole refrigerator has stopped cooling, say so, since that moves you up the list. Book online or call, and our callback sets a two-hour window.
More repairs in Edmonds
Ice Maker Repair nearby
Parts behind these calls
Book the $85 diagnostic visit
Checking an Edmonds ice maker costs $85; once you approve the repair, that amount lives inside the repair price, and if you don’t, it is all you pay.